العربية

Driven by power, built for reliability.

Industrial Power Systems Engineering in Egypt

Generator services, fuel systems, low-voltage panels, medium-voltage switchgear and transformers — from site survey and engineering to installation, testing, commissioning and maintenance.

Discuss your requirements Explore services Call +20 122 234 0600

ENGINEERING · SUPPLY · SERVICE

About HIPPO POWER SOLUTIONS

HIPPO POWER SOLUTIONS provides power engineering for industrial, commercial and mission-critical facilities across Egypt. We work across generation, fuel, control, protection, low- and medium-voltage distribution and transformers, with one accountable team from survey to commissioning and maintenance.

About our approach

FIVE SERVICE FAMILIES

Our Services

Each service page explains the typical scope, the engineering interfaces involved, and what is agreed after a site survey.

Technician checking a generator set with a multimeter and tablet

Generator Services

Preventive and corrective maintenance, troubleshooting, load testing, installation and commissioning for standby and prime-power applications.

View service scope: Generator Services
Engineers inspecting fuel transfer pumps, piping and a control panel beside a generator

Fuel Systems

Supply and installation of bulk and day tanks, transfer pumps, piping, filtration, leak detection, level monitoring and automatic fuel-control systems.

View service scope: Fuel Systems
Engineer inspecting wiring inside a low-voltage switchboard

Low-Voltage Panels

Engineering and supply of synchronisation (SYNC), PDP, MCC and ATS panels with metering, protection, load sharing and mains-parallel control.

View service scope: Low-Voltage Panels
Engineer performing relay testing on medium-voltage switchgear with a test set

MV Switchgear

Maintenance, breaker service, protection-relay testing, secondary injection, functional verification and commissioning of medium-voltage switchgear.

View service scope: MV Switchgear
Two engineers testing an oil-filled power transformer outdoors

Transformers

Installation, receiving inspection, insulation-resistance and turns-ratio testing, protection checks, commissioning and energisation support.

View service scope: Transformers

HOW WE ENGINEER AND VERIFY

Engineering Capabilities

Services describe what you can engage us for. Capabilities describe how the work is engineered and checked.

  1. Survey and load definition

    Site loads, operating modes, existing equipment and constraints are recorded before scope is fixed.

  2. Operating philosophy

    How sources, transfer, paralleling and load priorities should behave is defined before control and panel design.

  3. Protection and interlocks

    Relay logic, interlocks and trip philosophy are reviewed together with the equipment they protect.

  4. Testing and records

    Testing is planned against agreed acceptance criteria, and results are documented for handover.

SYSTEM-LEVEL ENGINEERING

Integrated Power Systems Engineering

The engineering challenge is usually the interface between generators, utility incomers, protection, fuel, LV/MV distribution, transformers and critical loads — not each item of equipment on its own.

How we approach integrated systems

Generator-to-generator paralleling

Sequencing, active (kW) and reactive (kVAr) load sharing and load-dependent start/stop.

Transfer and mains paralleling

Open-transition and closed-transition transfer, and sustained parallel operation where the design and approvals allow it.

Island and black-start operation

Defined recovery sequences for sites that must restore power without the utility supply.

Testing and commissioning

FAT, SAT and functional testing, with documented handover.

FROM REQUIREMENT TO RELIABLE OPERATION

Our Process

  1. Consultation & survey

    We define loads, operating modes, constraints and system interfaces.

  2. Design & engineering

    We coordinate equipment, controls, protection and documentation for the agreed scope.

  3. Supply & installation

    We supply and install the agreed package and coordinate interfaces with other trades.

  4. Testing & support

    We test, commission and hand over, and support the system in operation.

Equipment Experience

These logos identify equipment manufacturers our team has worked with. They do not indicate a partnership, dealership or manufacturer authorisation.

  • CAT
  • Perkins
  • ABB
  • Schneider Electric
  • ComAp
  • Deep Sea Electronics
  • Woodward
  • DEIF

POWER & FUEL-SYSTEM PRODUCTS

SmartGen & Holykell Products

Selected products for generator readiness and fuel-system monitoring, supported by application engineering.

SMARTGEN BAC2410

Battery charger

Charging generator starting batteries on 24 V nominal battery systems, with a 10 A charging-current rating.

SMARTGEN HT322

Engine water (coolant) heater

Keeping engine coolant warm on standby generators to support starting.

SMARTGEN HWP40N

Forced-circulation heater

Pre-heating engine coolant with a forced-circulation heater for generator sets.

HOLYKELL H1100

Fuel-level display instrument

Displaying fuel-tank level for generator fuel systems.

View product details

START THE CONVERSATION

Contact Us

Address
58 Mansoura St, Mit Ghamr, Dakahlia, Egypt

Send an enquiry

Tell us what the system must do. An engineer reviews each enquiry before we reply.

Fields marked * are required.

Equipment, ratings, quantities, site conditions or the problem you need solved.

We use these details only to respond to your enquiry. The form is delivered to our sales inbox by FormSubmit, a third-party form service. Read the privacy notice.

Prefer direct contact? +20 122 234 0600 ·